ГОСТ Р МЭК 61069-5-2017 Измерение, управление и автоматизация промышленного процесса. Определение свойств системы с целью ее оценки. Часть 5. Оценка надежности системы (Переиздание)

[1]

IEC 60300-3-1:2003, Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology

[2]

IEC 60050 (all parts), International Electrotechnical Vocabulary (available at http://www.electropedia.org)

[3]

IEC 60050-192:2015, International Electrotechnical Vocabulary - Part 192: Dependability

[4]

IEC 60068 (all parts), Environmental testing

[5]

IEC 60605-1:1978, Equipment reliability testing - Part 1: General requirements

________________

Заменен на IEC 60300-3-5:2001.

[6]

IEC 60605-2:1994, Equipment reliability testing - Part 2: Design of test cycles

[7]

IEC 60605-3 (all parts), Equipment reliability testing - Part 3: Preferred test conditions

________________

Стандарты данной серии отменены.

[8]

IEC 60605-4:2001, Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals

[9]

IEC 60605-6:2007, Equipment reliability testing - Part 6: Tests for the validity and estimation of the constant failure rate and constant failure intensity

[10]

IEC 60605-7:1978, Equipment reliability testing - Part 7: Compliance test plans for failure rate and mean time between failures assuming constant failure rate

________________

Заменен на IEC 61124:2012.

[11]

IEC 60706-4, Guide on maintainability of equipment - Part 4: Section 8: Maintenance and maintenance support planning

________________

Заменен на IEC 60300-3-14:2004.

[12]

IEC 60801 (all parts), Electromagnetic compatibility for industrial-process measurement and control equipment

[13]

IEC 60812:2006, Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)

________________

Заменен на IEC 60812:2018.

[14]

IEC 61000 (all parts), Electromagnetic compatibility (EMC)

[15]

IEC 61025:2006, Fault tree analysis (FTA)

[16]

IEC 61069-6, Industrial-process, control measurement and automation - Evaluation of system properties for the purpose of system assessment - Part 6: Assessment of system operability

[17]

IEC 61078, Analysis techniques for dependability - Reliability block diagram and boolean methods

[18]

IEC 61123, Reliability testing - Compliance test plans for success ratio

[19]

IEC 61165, Application of Markov techniques

[20]

IEC 61326 (all parts), Electrical equipment for measurement, control and laboratory use - EMC requirements  

[21]

IEC 61508 (all parts), Functional safety of electrical/electronic/programmable electronic safety-related systems

[22]

IEC 62443 (all parts), Industrial communication networks - Network and system security

[23]

IEC/TS 62603-1, Industrial process control systems - Guideline for evaluating process control systems - Part 1: Specifications

[24]

ISO/IEC 14764, Software Engineering - Software Life Cycle Processes - Maintenance USA Military Standardization Handbook MIL-HDBK-217 issues A through F, Reliability prediction of electronic equipment

УДК 658.5.012.7:006.354

ОКС 25.040.40

Ключевые слова: промышленный процесс, система измерения и управления, определение свойств системы, основная система управления, целевое назначение (миссия) системы, оценка надежности системы, влияющие факторы, свойства системы, методология оценки