Figure/reference | Identification | |
А | ||
abutment of raised edge | Figure 8 | 24 |
actual throat thickness | 3.19 | |
Figures 14 a), b) and 15 a) to f) | 14 | |
angle joint | 3.12; Figure 1 f) | |
angle of bevel | Figures 4, 5 and 7 | 17 |
annular projection diameter | Figure 9 c) | 32 |
annular projections | Figure 9 c) | |
arc stud weld | Figure 17 c) | |
В | ||
butt join | 3.7; Figure 1 a) | |
butt weld T-joint | Figure 13 d) | |
butt weld with flash (flash or friction) | Figure 17 b) | |
butt weld with upset | Figure 17 a) | |
С | ||
concave fillet weld | Figure 15 b) | |
configuration for foil-seam-welds | Figure 11 | |
configuration for spot, seam or mash welds | Figure 10 | |
convex fillet weld | Figure 15 a) | |
corner joint | 3.13; Figure 1 g) | |
cross joint | 3.16; Figure 1 j) | |
cruciform joint | 3.11; Figure 1 e) | |
D | ||
depth of preparation | Figures 4 and 7 | 18 |
depth of raised edge | Figure 8 | 25 |
depth of root face | Figures 3, 4, 5 and 7 | 12 |
design throat thickness | 3.18 | |
Figures 13 a) to d), 14 a), b) and 15 a) to f) | 13 | |
double row of staggered, spaced spot welds | Figure 17 f) | |
double V-butt weld | Figure 16 d) | |
E | ||
edge distance | Figure 9 a), b), c) | 33 |
Figure 17 f) | 43 | |
edge joint | 3.14; Figure 1 h) | |
effective throat thickness | 3.20 | 15 |
Figures 13 b), c), d), 14 a), b) and 15 a) to f) | ||
elongated projections | Figure 9 b) | |
excess weld metal | Figure 12 a), b) | 9 |
F | ||
faying surface | 3.4 | |
fillet weld | Figure 12 b) | |
fillet weld with deep penetration | Figure 15 f) | |
fillet weld with gap | Figure 15 c) | |
fillet weld with incomplete penetration | Figure 15 e) | |
fillet weld with unequal legs | Figure 15 d) | |
first run on the second side | Figure 16 d) | 24 |
flash | Figure 17 b), c) | 31 |
foil contact surface | Figure 11 | H |
foil length | Figure 11 | 36 |
foil thickness | Figure 11 | 38 |
foil width | Figure 11 | 37 |
forms of projection welds | Figure 9 | |
full penetration butt weld | Figure 13 b) | |
fusion face (fillet weld) | Figures 6 and 7 | I |
fusion face (prepared) | Figures 3, 4, 5 and 7 | E |
fusion face (unprepared) | Figures 2, 3 and 8 | D |
fusion line | Figure 12 a), b) | 6 |
fusion penetration | Figures 12 a), b), 16 e) | 5 |
fusion welding | 3.2 | |
fusion zone | Figure 12 a), b) | 26 |
G | ||
general view of butt weld | Figure 13 a) | |
H | ||
heat-affected zone | Figure 12 a), b) | 3 |
I | ||
included angle | Figures 3-7 | 21 |
incomplete penetration | 3.6 | |
incomplete penetration butt weld | Figure 13 c) | |
indentation | Figure 17 g) | 35 |
indentation depth | Figure 17 g) | 36 |
J | ||
joggle joint | Figure 18.39 | |
joint | 3.1 | |
joint length | Figures 2, 5 and 6 | 7 |
joint thickness | Figures 2-5 | 9 |
joint width | Figures 3-5 and 7 | 20 |
L | ||
land | Figure 5 | 44 |
lap joint | 3.9; Figure 1 c) | |
lap length | Figure 10 | 34 |
lapped area | Figure 10 | G |
lap width | Figure 10 | 35 |
layer of capping runs | Figure 16 a) to d) | 22 |
layers of filling runs | Figure 16 a) to d) | 21 |
leg length | 3.21 | 10 |
Figures 12 b) and 16 e) | ||
length of raised edge | Figure 8 | 22 |
longitudinal edge of preparation | Figures 5 and 7 | 8 |
longitudinal edge of root face | Figures 6 and 7 | 13 |
longitudinal side of raised edge | Figure 8 | 23 |
М | ||
maximum throat thickness | 3.17 | |
Figures 13 a) to d), 14 a), b) and 15 a) to f) | 12 | |
multiple joint | 3.15; Figure 1 i) | |
multi-run fillet weld | Figure 16 e) | |
N | ||
nugget diameter | Figure 17 d), e), g), h) | 33 |
nugget overlap | Figure 17 e) | 40 |
nugget thickness | Figure 17 g), h) | 34 |
P | ||
parallel joint | 3.8; Figure 1 b) | 1 |
parent metal | Figure 12 a), b) | |
partial penetration | 3.5 | 11 |
penetration bead thickness | Figures 12 a) and 16 a), b) | 27 |
pitch (of projections) | Figure 9 a), b), c) | С |
plate edge | Figure 2 | 1 |
plate thickness | Figures 2-6, 8, 9 a), 10, 11 | |
preparation for butt weld between plates with raised edges | Figure 8 | |
preparation for double-bevel T-butt welds | Figure 7 | |
preparation for fillet weld (T-joint) | Figure 6 | |
preparation for single bevel butt weld with backing | Figure 3 | |
preparation for single U-butt weld | Figure 5 | |
preparation for single V-butt weld | Figure 4 | |
preparation for square butt weld | Figure 2 | |
projection diameter | Figure 9 a) | 31 |
projection height | Figure 9 a), b), c) | 28 |
projection length | Figure 9 b) | 29 |
projection weld | Figure 17 h) | |
projection width | Figure 9 b), c) | 30 |
R | ||
radius of raised edge | Figure 8 | 26 |
resistance spot weld | Figure 17 g) | |
reverse side | Figures 2 and 3 | В |
root face | Figures 3-5 | F |
root gap | Figures 2-7 | 4 and 11 |
root of weld | Figure 12 a), b) | 7 |
root penetration | Figures 12 b) and 16 e) | 25 |
root radius | Figure 5 | 10 |
root run | Figure 16 a) to d) | 20 |
root width | Figure 13 a) | 27 |
round projections | Figure 9 a) | |
row pitch | Figure 17 f) | 42 |
S | ||
sealing run | Figure 16 c) | 23 |
seam weld | Figure 17 e) | |
side edge of preparation | Figures 4 and 7 | 15 |
side edge of root face | Figures 4, 5 and 7 | 14 |
side edge of workpiece | Figure 2 | 3 |
side of fusion face | Figure 2 | 6 |
side of gap face | Figures 2 and 10 | 5 |
single bevel T-butt weld | Figure 16 b) | |
single V-butt weld | Figure 12 a) | |
single V-butt weld with root face | Figure 16 a) | |
single V-butt weld with sealing run | Figure 16 c) | |
spot welds | Figure 17 d) | |
stagger | Figure 17 f) | 41 |
stud | Figure 17 c) | 45 |
Т | ||
throat thicknesses for fillet welds | Figure 14 | |
T-joint | 3.10; Figure 1 d) | |
toe | Figure 16 a) to e) | 19 |
typical examples of butt welds | Figure 13 | |
typical examples of fusion welds | Figure 12 | |
U | ||
upper workpiece surface | Figures 2 and 3 | A |
upset metal | Figure 17 a) | 30 |
W | W | |
welding using pressure | 3.3 | |
weld interface | Figure 17 a), b) | 37 |
weld length | Figure 13 a) | 17 |
Figure 17 e), f) | 38 | |
weld metal | Figure 12 a), b) | 2 |
weld nugget | Figure 17 g),h) | 32 |
weld pitch | Figure 17 d), f) | 39 |
weld pool backing | Figure 3 | X |
weld surface with bead ripples | Figure 13 a) | 18 |
weld toe angle | Figure 13 a) | 16 |
weld width | Figure 12 a) | 8 |
weld zone | Figures 12 a), b) and 17 a), b), c) | 4 |
width of preparation | Figures 4, 5 and 7 | 16 |
width of prepared face | Figure 4 | 19 |
workpiece width | Figure 11 | 2 |